A metal safety strap is provided with this boiler which is used to hold the boiler backplate against the plenum chamber once the boiler has been lifted into position but before any plenum chamber securing bolts have been fitted. Hard to say without testing but that's best advice. You must log in or register to reply here. I have called a plumber but he cannot get until tomorrow sometime, which is fine but I thought I would do a little investigating myself. If you use something like the Honeywell DT92E you can do it all around the programmer. 
| Uploader: | Gardabei |
| Date Added: | 4 March 2005 |
| File Size: | 59.68 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 83732 |
| Price: | Free* [*Free Regsitration Required] |
Reference should be made to Addendum 1Flue Lengths Criteria.
Fit the combustion chamber front coversecuring it with the four screws Accessories pack Item F. Refer to fault Finding Chart.
Started by RayP 17 minutes ago Replies: Connections which can be used and suggested methods of running pipework behind the boiler are shown in Fig. If a more coarse adjustment is necessarythe plenum chamber and mounting channel can be moved slightly up or down on the wall using the elongated holes in their mounting flanges. What outcome would you like to see from a vote of no confidence in the current Government?
Fit the terminal outer wall plate in positionlocating the end of the exhaust duct inside the circular connection of the wall plate grille. I would change the electrode and lead first as they're normally to blame and should be pretty cheap - but worst case - could be the PCB at fault. Furs up alot, its the water here, so heat exchanger needs occasional clean with ultrasonicator.
Replacing Netaheat 16-22, told whole system needs updating!!
I could do with a bit of basic advice about fitting a bigger radiator. Check that any other remote control connected in the system such as time clocks and thermostats 100 the boiler as required.
Welcome to AVForums on Xenforo 2. Mqnual I, and hopefully my plumber on the right track. If this is the case, I think I might get one for my parents. If the burner is igniting fully I would hazard a guess at the pcb being the problem.
I work for a big British company most people like to moan about and my dad has also worked for same company since the same age.
Potterton Netaheat 10/16 boiler not firing up | DIY Doctor UK DIY Forums
Remove the boiler from its carton and lay it front face downwards on a protective surfacesuch as its own carton. Potterton Amnual only - See Fig. To ensure continued efficient operation of the boilerit is necessary to carry out maintenance and cleaning at regular intervals.
To replace the insulation at the rear of the combustion chamber it will be necessary to remove the walls of the combustion chamber by unscrewing the four screws in the back panel and the nuts holding the panels to the heat exchanger.
Connect switched live supply from programmer or system controls to L. In this instance cut off the nozzle end of the upper duct so that not less than 25mm 1 in. Ensure that a good seal is obtained around the perimeter of the cover. Started by scott spock Wednesday at 9: Secure the pilot assembly to the main burner bracket with the two hexagon head screws. Our boiler is upstairs in a bedroom A little later while upstairs I thought the smell was more like burning plastic than TCP.
Remove and discard polystyrene cover.
Potterton netaheat 10 16 manual download
The thing I've noticed is that even though the pilot light lights, there is still manal spark from the electrode, which is within the flame, and a corresponding one in the electronic control box, every second. Which, as I see it, leaves the option of the red bottle simply not being able to accept any more water, or the valve is faulty at the red bottle end.
Carefully clean any deposits from around the fan motor and its supports. This item is not curently in our warehouse. Ensure that the capillary is secure in the clips provided. Been doing it since 16 and in 27 now.
I pottertno an account. If temperature control is required on the hot water systemadditional equipment is necessary and details are shown in Fig.
Комментариев нет:
Отправить комментарий